Manual Puddle Pump Kit | Tsurumi LSC1.4S, Pumps to 1mm
Pickup available at Warehouse - Epperstone, Nottingham (NG14 6AT)
Usually ready in 1 hour
View store informationBuilt for the job
Manual puddle pump kit for clearing floors down to 1mm
The Tsurumi LSC1.4S puddle sucker pump, supplied with 10m of 25mm reinforced hose and a stainless-steel clip.
This FPS Engineered™ kit pairs the Tsurumi LSC1.4S with the hose most of our customers add to it. Tsurumi manufacture the pump. The pump comes with its own 25mm hose tail, so the hose pushes straight on and the kit is ready to use. Choose 230V for buildings and domestic mains, or 110V for site use through a transformer.
Part of our pump kits, puddle pumps and Tsurumi ranges. Already have hose? The Tsurumi LSC1.4S is also sold on its own.
At a glance
- Pumps down to about 1mm on a reasonably flat floor.
- Up to 170 litres per minute and 11m head: the pump's maximum figures.
- Built-in non-return valve: water in the hose cannot run back when you switch off.
- 6mm free passage for sand, silt and small suspended material.
- Horizontal or vertical outlet to suit the hose route.
- 10m of 25mm reinforced hose that holds its shape over steps and thresholds.
- 3-year Tsurumi guarantee on the pump.
What's included
- 1 × Tsurumi LSC1.4S manual puddle sucker pump, 25mm outlet, with 10m heavy-duty rubber power cable
- 1 × 25mm hose tail, supplied with the pump
- 1 × 10m length of 25mm reinforced suction and delivery hose
- 1 × 20 to 32mm stainless-steel hose clip
How the kit connects
Push the hose fully over the pump's hose tail and tighten the clip. The outlet can be set horizontally or vertically: vertical for lifting straight out of a pit, horizontal where headroom is low and the hose needs to run away flat.
Prime the pump before first use.
The LSC1.4S must be filled with water before it starts. In shallow water, pour about 2.5 litres of clean water in through the outlet before switching on. The built-in non-return valve then holds that water in the pump, so it picks up quickly next time.
Manual operation
This is the manual LSC1.4S. It runs when the power is on and stops when you switch it off, which lets it keep working at very low water levels. It should be watched in use and switched off once water stops reaching the inlet. For unattended use, see the automatic LSC1.4S.
Technical specification
| Specification | Tsurumi LSC1.4S kit |
|---|---|
| Pump | Tsurumi LSC1.4S manual puddle sucker pump |
| Supply | 230V or 110V single phase |
| Motor power | 0.48 kW |
| Maximum flow | 170 litres per minute (pump maximum) |
| Maximum head | 11 metres |
| Minimum water level | About 1mm |
| Free passage | 6mm |
| Outlet | 25mm, horizontal or vertical, hose tail supplied |
| Non-return valve | Built into the pump |
| Power cable | 10m heavy-duty rubber |
| Hose | 10m of 25mm reinforced suction and delivery hose |
| Hose clip | 20 to 32mm stainless steel |
| Pump guarantee | 3 years, Tsurumi |
The flow and head figures are the pump's maximums. The flow you get through the hose will be lower, and falls as the lift and hose length increase. Work out a specific run with our pump performance calculator.
Limits and safe use
Drainage water and typical floodwater, solids to about 6mm. Not for raw sewage, heavily contaminated water, or water carrying large stones, leaves or fibrous material. Do not leave the pump running dry for long periods. Use the 110V model with a suitable 110V centre-tapped transformer.
Frequently asked questions
Do I need to buy a hose tail?
No. The LSC1.4S comes with its own 25mm hose tail, so the hose goes straight on with the supplied clip.
Why 25mm hose rather than 50mm?
This kit uses the standard 25mm outlet, which is lighter to handle and easier to store. A 50mm outlet version of the pump is available separately and loses less flow over long runs.
Which voltage should I choose?
110V for construction sites running through a transformer. 230V for buildings and domestic mains.
